Sand making machine is suitable for soft or hard and extremely hard materials crushing, which is widely used in a variety of ores, cement, refractories, aluminum where the soil clinker, emery, glass raw materials, mechanisms built stone gold slag, especially on thesilicon carbide, silicon carbide, sintered bauxite, United States sand contour hard, special hard and corrosion-resistant materials is higher than other types of crushers yield efficacy.Sand maker is also called impact crusher, whose application is wide, not only in hard materials, the great artificial sand used in material performance differences, pre-grinding ultra-fine crushing crushing cement, mining, refractories industry, such as: granite, basalt, limestone, quartz, gneiss, cement clinker, concrete aggregate, ceramic raw materials, iron ore, gold, copper, corundum, bauxite, silica.
When the skilled sand maker operators operate the sand making machine, they all have a set of methods which can improve production in the same application environment. Only mastered these methods can we make the enterprises to improve production efficiency, and sand making machine is not prone to problems. Here are the methods we sumarrised to increase the amount of sand making production.
First. we should always pay attention to the tightness of the sand making power transmission belts. If the belt is too loose when in use, it will affect the motor power passes to the sand making machine, when production naturally reduced. So usually use loose belt, we should be fastened in a timely manner.
Second, develop the habit of regular inspect sand internal parts wear. Such as Sand internal parts of the impeller and the liner wear is very common, if the serious side of the wear of these parts, while the other side of the lighter wear. At this time will affect the balance of the machine, and great damage to the machine. So when the discovery of these parts wear should timely replacement. But this is important to note, when replacement parts must be replaced at the same time, to ensure the consistency of both sides of the weight. Otherwise, both sides of the imbalance, the parts will still damage.
Third. The sand internal spindle is the main component of sand maker, its balance is important to the normal operation of the machine. But this place is very easy to get wear from time to time, therefore, it is required that we replace these parts when they wear. According to the experience of our technicians. It is more appropriate to replace the sand spindle every 7200 hours, in this period, we can clean the main bear every time, and then add the lubricant fill.
Company: Toronto pcs
Address: 222 Spadina Avenue, Unit # 116 A Toronto, ON - M5T3B3
Zip code: M5T3B3
Contact person: Fedrick Patrick
Phone: 647-693-5036
Email: fed.pats@gmail.com
More information can be found online at: [http://www.torontopcs.com]
When the skilled sand maker operators operate the sand making machine, they all have a set of methods which can improve production in the same application environment. Only mastered these methods can we make the enterprises to improve production efficiency, and sand making machine is not prone to problems. Here are the methods we sumarrised to increase the amount of sand making production.
First. we should always pay attention to the tightness of the sand making power transmission belts. If the belt is too loose when in use, it will affect the motor power passes to the sand making machine, when production naturally reduced. So usually use loose belt, we should be fastened in a timely manner.
Second, develop the habit of regular inspect sand internal parts wear. Such as Sand internal parts of the impeller and the liner wear is very common, if the serious side of the wear of these parts, while the other side of the lighter wear. At this time will affect the balance of the machine, and great damage to the machine. So when the discovery of these parts wear should timely replacement. But this is important to note, when replacement parts must be replaced at the same time, to ensure the consistency of both sides of the weight. Otherwise, both sides of the imbalance, the parts will still damage.
Third. The sand internal spindle is the main component of sand maker, its balance is important to the normal operation of the machine. But this place is very easy to get wear from time to time, therefore, it is required that we replace these parts when they wear. According to the experience of our technicians. It is more appropriate to replace the sand spindle every 7200 hours, in this period, we can clean the main bear every time, and then add the lubricant fill.
Company: Toronto pcs
Address: 222 Spadina Avenue, Unit # 116 A Toronto, ON - M5T3B3
Zip code: M5T3B3
Contact person: Fedrick Patrick
Phone: 647-693-5036
Email: fed.pats@gmail.com
More information can be found online at: [http://www.torontopcs.com]
SHARE
