Home & Garden Landscaping & Garden & Landscape

Troy-Bilt Super Bronco Deck Leveling Instructions

    • 1). Park your Troy-Bilt Super Bronco mower and turn off the engine.

    • 2). Move the deck lift lever on the Super Bronco's side to the middle position, then unmount the lawn mower and open the engine hood.

    • 3). Remove the black ignition wire from the back of the Troy-Bilt Super Bronco mower's spark plug.

    • 4). Cover your hands with a pair of gloves and find the discharge chute on the bottom of the Troy-Bilt Super Bronco mower. The chute will lie parallel to the rest of the deck assembly. Ensure the blade is aligned straight from the front of the mower to the rear. Measure the blade closest to the discharge chute with a ruler by checking the distance from the blade's tip to the ground.

    • 5). Measure the rearmost blade from its tip to the ground.

    • 6). Locate the mower's long suspension arm. It will be near the blades you measured on the Troy-Bilt mower's bottom. There is a nut on this arm that controls the levelness of the blades you just measured. Adjust this hex nut with a socket wrench in order to level the blades depending upon what your measurements revealed. Loosen the nut to lower the front-to-rear orientation of the deck, or tighten the nut to raise the front-to-rear orientation. Ensure the blade becomes level from front to rear after your adjustments.

    • 7). Rotate the Troy-Bilt Super Bronco mower's blade so that it runs side to side (perpendicular to the mower's direction) in preparation of further measurements.

    • 8). Find the Troy-Bilt Super Bronco mower's hangar bracket. It resides beside the blade on the mower's left side. Loosen the hex bolt on this bracket with your socket wrench.

    • 9). Measure the Troy-Bilt Super Bronco mower's blade the same way you did previously. Locate the adjustment gear on the hangar bracket, then tighten its bolt to raise the sides of the deck if necessary. Alternatively, loosen the bolt to lower the deck's sides until the blade is level when measured side to side.

    • 10

      Use the socket wrench to tighten the Troy-Bilt Super Bronco mower's hex bolt back into place.

    • 11

      Reconnect the mower's ignition wire to the spark plug.

SHARE
RELATED POSTS on "Home & Garden"
Give Your Home a Fighting Chance In the Great British Climate
Give Your Home a Fighting Chance In the Great British Climate
Lazy Lawn Care - Getting Away With the Minimum
Lazy Lawn Care - Getting Away With the Minimum
The Time to Plant Grass Seed in the Spring
The Time to Plant Grass Seed in the Spring
Vinyl Fencing Presents an Easier to Maintain Alternative to Wooden Fencing
Vinyl Fencing Presents an Easier to Maintain Alternative to Wooden Fencing
What Causes Ruts in a Lawn?
What Causes Ruts in a Lawn?
How to Design & Install Landscaping
How to Design & Install Landscaping
Arizona Ash Trees
Arizona Ash Trees
Concrete Gatefront Entry Ideas
Concrete Gatefront Entry Ideas
How to Make a Pickaxe in "Stranded 2"
How to Make a Pickaxe in "Stranded 2"
FAQ on Fences
FAQ on Fences
How to Install a Sliding Fence Gate
How to Install a Sliding Fence Gate
How to Repair a Mower Wheel
How to Repair a Mower Wheel
How to Dig Up Rocks in My Lawn Quickly
How to Dig Up Rocks in My Lawn Quickly
Toro 51599 Ultra 12 Amp Variable-Speed Electric Blower-Vacuum Review - Top Eco-friendly Blower
Toro 51599 Ultra 12 Amp Variable-Speed Electric Blower-Vacuum Review - Top Eco-friendly Blower
How to Get Paid for Mowing a Lawn
How to Get Paid for Mowing a Lawn
How to Replace a Mower Belt on a Snapper Riding Mower
How to Replace a Mower Belt on a Snapper Riding Mower
Fence Repair Ideas
Fence Repair Ideas
What Is the Origin of Lawn Ornaments?
What Is the Origin of Lawn Ornaments?
How to Make Grass Grow in Red Clay Soil
How to Make Grass Grow in Red Clay Soil
Garden Water Pond - Bring Relaxation Home With You
Garden Water Pond - Bring Relaxation Home With You
Simple DIY Backyard Ideas on a Budget
Simple DIY Backyard Ideas on a Budget
Do it Yourself Pergola Covers
Do it Yourself Pergola Covers
How to Replace the Drive Belt on a Craftsman GT3000
How to Replace the Drive Belt on a Craftsman GT3000

Leave Your Reply

*