If an individual is seeking to grow their plants inside a structure, while the plants should normally be exposed to the rays of the sun, then they can do so by using grow lights. In general, a grow light that serves for commercial purposes is not very affordable, that is why it might be better for an individual to design their own grow light by employing commonly accessible components. To make a grow light is not simply about to build a light. Indeed, the person who seeks to build their own grow light needs to find the right balance regarding the intensity of the grow light, the distance of the plants from the source of light, and the total amount of time during which the plants ought to be exposed. In this article, we will discuss about a few ideas for the making of both an effective and efficient grow light setup.
An individual can use 2 regular four foot fluorescent light fixtures to build a grow light for their plants. To do so, the person must shear a sheet of plywood that is slightly bigger than the two regular 4 foot fluorescent light fixtures. Then, the person needs to pierce holes in the rears of the two fixtures and insert screws in them so that they can be attached to the plywood edge by edge. The person should use four screws to make sure that it is properly done. The individual must then connect irons from one corner to another in order to have 2 loops at each end. Some hooks must be screwed to the roof above the seedling trays and the individual can position the grow lights at the height of their choice. The two regular four foot fluorescent light fixtures need to be connected to an electric junction of the roof. The bulbs of the fluorescent light fixtures will supply appropriate light to the plants if they are turned on during an entire day. However, if the person prefers to employ full spectrum bulbs, then they should refer to the recommendations of the manufacturer as for the optimal length of time during which the plants can be exposed. One thing that the person is strongly advised to do is to make sure that the grow lights are not positioned too close to the plants or they are very likely to burn. The overexposure of the plants under the grow light also provokes the sun-burning of the plants.
LED light fixtures can also be connected to an identical plywood and positioned in the same way as the fluorescent light fixtures were in the roof in the first scenario. LED light fixtures that contain 90 watts of battery are capable of generating a growing light comparable to a four-hundred metal halide. LED light fixtures are made with diodes that can be employed for over one hundred thousand hours and that require less than thirty three per cent of the energy that other light sources need.
If the person is trying to make their plants benefit from the light in an even way, then they will need to place white surfaces around the area where the plants are grown. Indeed, walls that have a white painting have the ability to reject the light that they receive and make sure that the plants do not only grow in one single direction. Effectively, it has been found that plants can have a better health and resist more when the light that they receive is distributed in a better and more effective way. The sole change that must be made is the increase or the reduction of the height of the grow light that is on the roof.
An individual can use 2 regular four foot fluorescent light fixtures to build a grow light for their plants. To do so, the person must shear a sheet of plywood that is slightly bigger than the two regular 4 foot fluorescent light fixtures. Then, the person needs to pierce holes in the rears of the two fixtures and insert screws in them so that they can be attached to the plywood edge by edge. The person should use four screws to make sure that it is properly done. The individual must then connect irons from one corner to another in order to have 2 loops at each end. Some hooks must be screwed to the roof above the seedling trays and the individual can position the grow lights at the height of their choice. The two regular four foot fluorescent light fixtures need to be connected to an electric junction of the roof. The bulbs of the fluorescent light fixtures will supply appropriate light to the plants if they are turned on during an entire day. However, if the person prefers to employ full spectrum bulbs, then they should refer to the recommendations of the manufacturer as for the optimal length of time during which the plants can be exposed. One thing that the person is strongly advised to do is to make sure that the grow lights are not positioned too close to the plants or they are very likely to burn. The overexposure of the plants under the grow light also provokes the sun-burning of the plants.
LED light fixtures can also be connected to an identical plywood and positioned in the same way as the fluorescent light fixtures were in the roof in the first scenario. LED light fixtures that contain 90 watts of battery are capable of generating a growing light comparable to a four-hundred metal halide. LED light fixtures are made with diodes that can be employed for over one hundred thousand hours and that require less than thirty three per cent of the energy that other light sources need.
If the person is trying to make their plants benefit from the light in an even way, then they will need to place white surfaces around the area where the plants are grown. Indeed, walls that have a white painting have the ability to reject the light that they receive and make sure that the plants do not only grow in one single direction. Effectively, it has been found that plants can have a better health and resist more when the light that they receive is distributed in a better and more effective way. The sole change that must be made is the increase or the reduction of the height of the grow light that is on the roof.
SHARE