There are many factors that can damage your fiber glass boat hull, such as rot, collisions, and consistently running aground.
If ignored despite the severe damage, it could lead to severe problems such as flooding or eventual sinking of the boat.
If the damage to the hull is severe, it needs to be taken out of the water.
On the other hand, if there is slight damage, it can be repaired while the boat is docked.
• The first step on how to repair a fiberglass hull on boats is to cut and totally remove the damaged area as well as the neighboring regions.
When necessary, you should be working within the boat.
• With a de-waxing solvent, eliminate the wax from within and outside of the damaged area.
• Use sand paper to sand the area surrounding the damaged area outside and inside.
• Apply a coating of paste wax on the outside of the damaged area making sure you avoid the edges • When applying a piece of Formica, make sure that it is bigger than the damaged area to be repaired.
Add polyvinyl alcohol to the Formica and tape it on the outer hull.
When necessary, use a heat gun as a molding for the Formica although it will do well on its own.
• Cut out a piece of fabric from fiberglass 1 inch bigger than the damaged area.
Depending on the extent of the hole, cut several pieces of fabric.
Use a couple of 1.
5 ounce mats alternating with 6 ounce cloths.
The succeeding layers should be 12 inches bigger than the previous.
• In applying resin and a catalyst, just follow the directions in the repair kit.
For repairs, you should use epoxy but make sure it is below the water line and without a gel coat.
• From inside the boat, paint or spray the gel to the Formica at least 20 millimeters thick.
• Use polyester resin to wet the fabric and mat.
Apply the first three layers to the coating using a resin roller to smoothen the bubbles.
Afterwards apply the next four layers.
Avoid applying more than four layers simultaneously.
• The last piece of mat should be 1 inch bigger than the repair area.
Using a resin roller, apply resin for a finished appearance.
Use polyvinyl alcohol to seal the layer.
• Remove the backing and finish the imperfections with gel coating.
Learning these steps on how to repair a fiberglass hull on boats yourself will result to more savings on maintenance and repair.
If ignored despite the severe damage, it could lead to severe problems such as flooding or eventual sinking of the boat.
If the damage to the hull is severe, it needs to be taken out of the water.
On the other hand, if there is slight damage, it can be repaired while the boat is docked.
• The first step on how to repair a fiberglass hull on boats is to cut and totally remove the damaged area as well as the neighboring regions.
When necessary, you should be working within the boat.
• With a de-waxing solvent, eliminate the wax from within and outside of the damaged area.
• Use sand paper to sand the area surrounding the damaged area outside and inside.
• Apply a coating of paste wax on the outside of the damaged area making sure you avoid the edges • When applying a piece of Formica, make sure that it is bigger than the damaged area to be repaired.
Add polyvinyl alcohol to the Formica and tape it on the outer hull.
When necessary, use a heat gun as a molding for the Formica although it will do well on its own.
• Cut out a piece of fabric from fiberglass 1 inch bigger than the damaged area.
Depending on the extent of the hole, cut several pieces of fabric.
Use a couple of 1.
5 ounce mats alternating with 6 ounce cloths.
The succeeding layers should be 12 inches bigger than the previous.
• In applying resin and a catalyst, just follow the directions in the repair kit.
For repairs, you should use epoxy but make sure it is below the water line and without a gel coat.
• From inside the boat, paint or spray the gel to the Formica at least 20 millimeters thick.
• Use polyester resin to wet the fabric and mat.
Apply the first three layers to the coating using a resin roller to smoothen the bubbles.
Afterwards apply the next four layers.
Avoid applying more than four layers simultaneously.
• The last piece of mat should be 1 inch bigger than the repair area.
Using a resin roller, apply resin for a finished appearance.
Use polyvinyl alcohol to seal the layer.
• Remove the backing and finish the imperfections with gel coating.
Learning these steps on how to repair a fiberglass hull on boats yourself will result to more savings on maintenance and repair.
SHARE
